Latest Responses
- High Feed End Mill feed and speeds by Eldar Gerfanov (Admin) on September 7
- Suggestions by Eldar Gerfanov (Admin) on July 27
- Corner Rounding End Mill FSwizard and HSMA by riplash2008 on July 12
- New user help with entering values by Eldar Gerfanov (Admin) on May 24
- Tool stick-out invalid by User10807 on May 11
- Thread mill RPM and resulting Feed by User10805 on April 26
Help, Suport and Discussions related to HSMAdvisor Speed and Feed Calculator
| 50 views |
4 answers |
High Feed End Mill feed and speedsBy riplash2008 on September 6, 2023, 1:31 pmLast Reply: Eldar Gerfanov (Admin) on September 7, 2023, 10:16 am |
|
| 17 views |
adding new machine speedio s500x1 16k spindleBy machiningvapors on August 10, 2023, 6:50 am |
||
| 72 views |
3 answers |
Tool stick-out invalidBy User10807 on April 28, 2023, 4:06 pmLast Reply: User10807 on May 11, 2023, 12:11 pm |
|
| 16 views |
CBN Speeds and feedsBy Timberwerkz on April 28, 2023, 8:07 am |
||
| 52 views |
4 answers |
Thread mill RPM and resulting FeedBy User10805 on April 23, 2023, 1:31 amLast Reply: User10805 on April 26, 2023, 8:48 pm |
|
| 14 views |
Expanded PVC Workpiece RecommendationsBy SteveMills on April 26, 2023, 9:04 am |
||
| 57 views |
3 answers |
Coating Al2O3By Timberwerkz on March 27, 2023, 8:49 amLast Reply: Eldar Gerfanov (Admin) on April 8, 2023, 10:09 pm |
|
| 53 views |
1 answer |
Contant Surface Speed IN LATHEBy taydevs on February 16, 2023, 12:08 pmLast Reply: Eldar Gerfanov (Admin) on April 3, 2023, 9:08 pm |
|
| 64 views |
1 answer |
Resulting RPM was reduced because of the lenght of the tool?By TomStone on April 2, 2023, 4:32 amLast Reply: Eldar Gerfanov (Admin) on April 2, 2023, 9:34 am |
|
| 42 views |
1 answer |
Tool size limited to two digitsBy ddexdd on March 2, 2023, 6:51 pmLast Reply: Eldar Gerfanov (Admin) on March 24, 2023, 4:22 pm |
|
| 47 views |
3 answers |
Favorite Materials ListBy tkrohn on March 10, 2023, 2:15 pmLast Reply: Eldar Gerfanov (Admin) on March 11, 2023, 11:07 am |
|
| 45 views |
1 answer |
Coatings PVD AlTiCrSiNBy ATCAdmin on March 3, 2023, 6:11 pmLast Reply: Eldar Gerfanov (Admin) on March 3, 2023, 6:18 pm |
|
| 60 views |
1 answer |
Threadmill questionsBy rronald on February 24, 2023, 10:28 amLast Reply: Eldar Gerfanov (Admin) on February 27, 2023, 10:35 pm |
|
| 33 views |
1 answer |
Spot drill feed rateBy rronald on February 22, 2023, 10:12 amLast Reply: Eldar Gerfanov (Admin) on February 22, 2023, 6:02 pm |
|
| 47 views |
1 answer |
Add toolBy pkv13 on January 20, 2023, 6:54 amLast Reply: Eldar Gerfanov (Admin) on January 24, 2023, 11:00 am |
|
| 110 views |
2 answers |
Breakthrough amount in Calculation ReportBy reedfirst on December 10, 2022, 4:11 pmLast Reply: Eldar Gerfanov (Admin) on December 19, 2022, 1:50 am |
|
| 105 views |
3 answers |
Confusing Circle/Ramp outputBy Sperciv on October 27, 2022, 4:34 amLast Reply: Sperciv on October 28, 2022, 4:45 am |
|
| 70 views |
2 answers |
V-point dowel drill help for newbieBy StevenRosburg on August 21, 2022, 11:43 pmLast Reply: StevenRosburg on August 22, 2022, 11:18 am |
|
| 75 views |
2 answers |
Lost tool database :(By ndlsjk on August 18, 2022, 10:15 amLast Reply: Eldar Gerfanov (Admin) on August 18, 2022, 4:47 pm |
|
| 133 views |
2 answers |
Add ToolBy asic_david on May 5, 2022, 7:25 amLast Reply: asic_david on May 5, 2022, 10:01 am |
© 2009-2022 Eldar Gerfanov. All Rights Reserved.
© 2009 Eldar Gerfanov. Materials on this site are presented as is and are mostly for educational use.
You may freely reproduce information presented herein without any consent from me, provided you include link to this site.
In case when i am not the copyright holder, you may want to contact proper owner of material. Anyway, they are freely available on the Internet.
If you hold the copyright right for any of the materials on this site and want them removed, please contact me here