Latest Responses
- High Feed End Mill feed and speeds by Eldar Gerfanov (Admin) on September 7
- Suggestions by Eldar Gerfanov (Admin) on July 27
- Corner Rounding End Mill FSwizard and HSMA by riplash2008 on July 12
- New user help with entering values by Eldar Gerfanov (Admin) on May 24
- Tool stick-out invalid by User10807 on May 11
- Thread mill RPM and resulting Feed by User10805 on April 26
Help, Suport and Discussions related to HSMAdvisor Speed and Feed Calculator
| 958 views |
9 answers |
Few questionsBy Yosiu on September 23, 2017, 4:53 amLast Reply: Eldar Gerfanov (Admin) on March 6, 2019, 7:21 am |
|
| 258 views |
2 answers |
Tool Type V-Bit Engraver Table QuestionBy cobra514 on January 20, 2019, 10:11 pmLast Reply: cobra514 on January 21, 2019, 4:04 pm |
|
| 170 views |
2 answers |
Small feature request for my convenience :)By ndlsjk on December 29, 2018, 4:23 pmLast Reply: Eldar Gerfanov (Admin) on January 21, 2019, 12:57 pm |
|
| 192 views |
3 answers |
TappingBy serge.nelissen on December 2, 2018, 12:37 pmLast Reply: Eldar Gerfanov (Admin) on December 3, 2018, 7:12 pm |
|
| 455 views |
4 answers |
WOC and DOCBy serge.nelissen on December 2, 2018, 3:18 pmLast Reply: serge.nelissen on December 3, 2018, 6:19 pm |
|
| 116 views |
2 answers |
Cross sectionBy serge.nelissen on December 2, 2018, 10:55 amLast Reply: serge.nelissen on December 2, 2018, 11:54 am |
|
| 210 views |
11 answers |
Generic materialsBy serge.nelissen on December 1, 2018, 2:36 pmLast Reply: serge.nelissen on December 2, 2018, 11:40 am |
|
| 163 views |
5 answers |
New layout?By ndlsjk on November 13, 2018, 11:15 amLast Reply: ndlsjk on November 28, 2018, 11:51 am |
|
| 117 views |
3 answers |
mm dimension for chip load and all other dims in inchesBy blcavender on November 27, 2018, 3:34 pmLast Reply: blcavender on November 27, 2018, 8:38 pm |
|
| 197 views |
3 answers |
Tapered cuttersBy DaveF on October 2, 2018, 5:17 amLast Reply: Eldar Gerfanov (Admin) on October 2, 2018, 11:12 am |
|
| 202 views |
2 answers |
DOC limited to twice the tool Die??By ktm3301 on August 16, 2018, 8:03 pmLast Reply: ktm3301 on August 20, 2018, 5:06 pm |
|
| 176 views |
2 answers |
negitive RPM on tap speeds??By ktm3301 on August 15, 2018, 2:35 amLast Reply: Eldar Gerfanov (Admin) on August 15, 2018, 6:06 am |
|
| 327 views |
4 answers |
Metric ImperialBy iang on February 28, 2018, 10:45 amLast Reply: Stevemanchester on August 10, 2018, 2:13 am |
|
| 890 views |
1 answer |
Difference between app and desktopBy bogger461 on July 31, 2018, 11:18 amLast Reply: Eldar Gerfanov (Admin) on August 1, 2018, 12:02 am |
|
| 379 views |
7 answers |
few general questionsBy CS900 on May 7, 2018, 3:00 pmLast Reply: CS900 on May 9, 2018, 2:56 pm |
|
| 1173 views |
4 answers |
Crucible (CPM 10V) vs Uddeholm (Vanadis 10 SuperClean)By jday57 on April 4, 2018, 3:53 pmLast Reply: jday57 on April 18, 2018, 12:32 pm |
|
| 329 views |
1 answer |
error editing Machine DefinitionBy CHB on March 16, 2018, 11:19 amLast Reply: Eldar Gerfanov (Admin) on March 17, 2018, 10:22 am |
|
| 1142 views |
4 answers |
Cutting ForceBy CHB on July 11, 2017, 1:15 pmLast Reply: Eldar Gerfanov (Admin) on March 4, 2018, 5:58 pm |
|
| 285 views |
1 answer |
v1.526 Kaspersky ProblemBy kinseyjr21 on March 1, 2018, 7:10 amLast Reply: Eldar Gerfanov (Admin) on March 1, 2018, 7:57 am |
|
| 276 views |
1 answer |
PrintoutBy PointFive55 on February 28, 2018, 2:39 pmLast Reply: Eldar Gerfanov (Admin) on February 28, 2018, 5:01 pm |
© 2009-2022 Eldar Gerfanov. All Rights Reserved.
© 2009 Eldar Gerfanov. Materials on this site are presented as is and are mostly for educational use.
You may freely reproduce information presented herein without any consent from me, provided you include link to this site.
In case when i am not the copyright holder, you may want to contact proper owner of material. Anyway, they are freely available on the Internet.
If you hold the copyright right for any of the materials on this site and want them removed, please contact me here