Latest Responses
- mm/sec units by Eldar Gerfanov on August 15
- minimum RPM by Eldar Gerfanov on June 5
- Add Tool by asic_david on May 5
- Choosing a Material only listed in the "cross reference" by Aaron on April 4
- Microsoft Surface for HSM Advisor? by Aaron on April 3
- Long reach endmill with tapered shoulder by Eldar Gerfanov on March 29
- Climb vs Conventional by Eldar Gerfanov on March 13
- Tormach 8L High Speed Profile by Eldar Gerfanov on March 6
- Aluminium 5000 Series (5083) Feed in HSM to low or material inhomogenious ? by Eldar Gerfanov on February 26
- Please add 1.4057 QT800/QT900 by Eldar Gerfanov on January 23
Help, Suport and Discussions related to HSMAdvisor Speed and Feed Calculator
1512 views |
1 answer |
Feed rateBy cunder on October 9, 2014, 6:57 amLast Reply: Eldar Gerfanov on October 9, 2014, 11:19 am |
|
1479 views |
1 answer |
Slitting SawBy Blue_Chips on September 22, 2014, 8:11 amLast Reply: Eldar Gerfanov on September 22, 2014, 9:28 am |
|
1527 views |
2 answers |
Pyramid EngraverBy Otter on September 14, 2014, 11:02 pmLast Reply: Otter on September 14, 2014, 11:16 pm |
|
1675 views |
3 answers |
6063-t5 aluminum dataBy Otter on September 1, 2014, 9:30 pmLast Reply: Otter on September 10, 2014, 12:40 am |
|
1488 views |
7 answers |
HSM for windowsBy da1e11oyd on September 4, 2014, 11:45 pmLast Reply: Eldar Gerfanov on September 7, 2014, 8:47 pm |
|
1358 views |
1 answer |
bug reportBy jack on August 30, 2014, 8:11 amLast Reply: Eldar Gerfanov on August 30, 2014, 11:43 am |
|
1821 views |
3 answers |
confuse about Chip thinning and HSMBy jack on August 29, 2014, 3:19 amLast Reply: Eldar Gerfanov on August 29, 2014, 11:21 am |
|
1362 views |
4 answers |
Ball nose in tool type missing?By Blue_Chips on August 21, 2014, 1:21 pmLast Reply: Eldar Gerfanov on August 22, 2014, 7:04 pm |
|
1422 views |
1 answer |
Helix AngleBy cunder on August 19, 2014, 6:50 amLast Reply: Eldar Gerfanov on August 19, 2014, 1:08 pm |
|
1552 views |
2 answers |
Sub Forums (Fora) for specific CAM PackagesBy Magicniner on January 20, 2014, 6:34 amLast Reply: Eldar Gerfanov on August 16, 2014, 10:30 pm |
|
1364 views |
2 answers |
Turning-ProfilingBy Hulsaver on August 11, 2014, 6:46 amLast Reply: Eldar Gerfanov on August 11, 2014, 1:12 pm |
|
1427 views |
1 answer |
lathe partingBy Aero on July 9, 2014, 5:23 pmLast Reply: Eldar Gerfanov on July 9, 2014, 10:59 pm |
|
2844 views |
12 answers |
Screen IssuesBy Blue_Chips on April 29, 2014, 7:05 pmLast Reply: Eldar Gerfanov on June 25, 2014, 9:22 pm |
|
1519 views |
3 answers |
Trouble adding toolBy Steve Lucas on June 13, 2014, 10:16 amLast Reply: Steve Lucas on June 17, 2014, 1:19 pm |
|
1800 views |
5 answers |
SuggestionBy Blue_Chips on May 1, 2014, 8:55 amLast Reply: Eldar Gerfanov on May 5, 2014, 11:26 am |
|
1820 views |
7 answers |
Feed not updating after DOC of from .050 - .100 inchBy Blue_Chips on May 3, 2014, 8:30 amLast Reply: Blue_Chips on May 3, 2014, 9:08 pm |
|
1846 views |
1 answer |
ISO Fine ThreadsBy Blue_Chips on April 29, 2014, 5:14 pmLast Reply: Eldar Gerfanov on April 29, 2014, 10:14 pm |
|
1731 views |
1 answer |
SurveyBy Blue_Chips on April 29, 2014, 6:16 pmLast Reply: Eldar Gerfanov on April 29, 2014, 10:10 pm |
|
1651 views |
1 answer |
pop up window?By Steve Lucas on April 3, 2014, 7:16 amLast Reply: Eldar Gerfanov on April 3, 2014, 11:19 am |
|
2446 views |
4 answers |
Cusp height calculator? [added]By Steve Lucas on December 11, 2013, 7:03 amLast Reply: Eldar Gerfanov on April 2, 2014, 7:32 pm |
© 2009-2022 Eldar Gerfanov. All Rights Reserved.
© 2009 Eldar Gerfanov. Materials on this site are presented as is and are mostly for educational use.
You may freely reproduce information presented herein without any consent from me, provided you include link to this site.
In case when i am not the copyright holder, you may want to contact proper owner of material. Anyway, they are freely available on the Internet.
If you hold the copyright right for any of the materials on this site and want them removed, please contact me here