Latest Responses
Help, Suport and Discussions related to HSMAdvisor Speed and Feed Calculator
| 659 views |
13 answers |
Tool infoBy serge.nelissen on November 29, 2018, 3:41 pmLast Reply: Eldar Gerfanov (Admin) on April 19, 2019, 12:40 am |
|
| 463 views |
1 answer |
Conical Barrel ToolsBy Karl.Oram on April 13, 2019, 3:55 pmLast Reply: Eldar Gerfanov (Admin) on April 14, 2019, 1:48 am |
|
| 722 views |
9 answers |
Broken End MillsBy serge.nelissen on March 17, 2019, 3:57 pmLast Reply: serge.nelissen on April 2, 2019, 10:56 pm |
|
| 405 views |
1 answer |
Special CoatingsBy That1Guy on April 2, 2019, 3:00 amLast Reply: Eldar Gerfanov (Admin) on April 2, 2019, 3:11 am |
|
| 434 views |
6 answers |
Default values not appliedBy serge.nelissen on March 17, 2019, 3:43 pmLast Reply: serge.nelissen on March 18, 2019, 5:28 pm |
|
| 1260 views |
9 answers |
Few questionsBy Yosiu on September 23, 2017, 9:53 amLast Reply: Eldar Gerfanov (Admin) on March 6, 2019, 12:21 pm |
|
| 568 views |
2 answers |
Tool Type V-Bit Engraver Table QuestionBy cobra514 on January 21, 2019, 3:11 amLast Reply: cobra514 on January 21, 2019, 9:04 pm |
|
| 422 views |
2 answers |
Small feature request for my convenience :)By ndlsjk on December 29, 2018, 9:23 pmLast Reply: Eldar Gerfanov (Admin) on January 21, 2019, 5:57 pm |
|
| 465 views |
3 answers |
TappingBy serge.nelissen on December 2, 2018, 5:37 pmLast Reply: Eldar Gerfanov (Admin) on December 4, 2018, 12:12 am |
|
| 748 views |
4 answers |
WOC and DOCBy serge.nelissen on December 2, 2018, 8:18 pmLast Reply: serge.nelissen on December 3, 2018, 11:19 pm |
|
| 366 views |
2 answers |
Cross sectionBy serge.nelissen on December 2, 2018, 3:55 pmLast Reply: serge.nelissen on December 2, 2018, 4:54 pm |
|
| 465 views |
11 answers |
Generic materialsBy serge.nelissen on December 1, 2018, 7:36 pmLast Reply: serge.nelissen on December 2, 2018, 4:40 pm |
|
| 477 views |
5 answers |
New layout?By ndlsjk on November 13, 2018, 4:15 pmLast Reply: ndlsjk on November 28, 2018, 4:51 pm |
|
| 402 views |
3 answers |
mm dimension for chip load and all other dims in inchesBy blcavender on November 27, 2018, 8:34 pmLast Reply: blcavender on November 28, 2018, 1:38 am |
|
| 478 views |
3 answers |
Tapered cuttersBy DaveF on October 2, 2018, 10:17 amLast Reply: Eldar Gerfanov (Admin) on October 2, 2018, 4:12 pm |
|
| 469 views |
2 answers |
DOC limited to twice the tool Die??By ktm3301 on August 17, 2018, 1:03 amLast Reply: ktm3301 on August 20, 2018, 10:06 pm |
|
| 456 views |
2 answers |
negitive RPM on tap speeds??By ktm3301 on August 15, 2018, 7:35 amLast Reply: Eldar Gerfanov (Admin) on August 15, 2018, 11:06 am |
|
| 583 views |
4 answers |
Metric ImperialBy iang on February 28, 2018, 3:45 pmLast Reply: Stevemanchester on August 10, 2018, 7:13 am |
|
| 1196 views |
1 answer |
Difference between app and desktopBy bogger461 on July 31, 2018, 4:18 pmLast Reply: Eldar Gerfanov (Admin) on August 1, 2018, 5:02 am |
|
| 674 views |
7 answers |
few general questionsBy CS900 on May 7, 2018, 8:00 pmLast Reply: CS900 on May 9, 2018, 7:56 pm |
© 2009-2022 Eldar Gerfanov. All Rights Reserved.
© 2009 Eldar Gerfanov. Materials on this site are presented as is and are mostly for educational use.
You may freely reproduce information presented herein without any consent from me, provided you include link to this site.
In case when i am not the copyright holder, you may want to contact proper owner of material. Anyway, they are freely available on the Internet.
If you hold the copyright right for any of the materials on this site and want them removed, please contact me here