Discussions on general subject, as well as questions and suggestions concerning FSWizard in general
Pages:(4) [1] 2 3 4
 
 
273
views
1
answer

Future sharing of work account

By TheHow7zer on March 21, 2025, 7:57 am
Last Reply: Eldar Gerfanov (Admin) on March 22, 2025, 11:26 pm
 
 
1363
views
4
answers

Request to add PU Epoxy Tooling Board density 45lb/ft^3

By dhanushkk on December 10, 2024, 2:03 pm
Last Reply: dhanushkk on December 13, 2024, 9:55 am
 
 
2113
views
3
answers

Ball endmill/surfacing example

By rlockwood on September 18, 2013, 11:54 am
Last Reply: Eldar Gerfanov (Admin) on September 19, 2024, 10:52 pm
 
 
402
views
3
answers

HSMA speeds and feeds with plastic and O-flutes

By riplash2008 on January 5, 2024, 2:49 pm
Last Reply: MikeHorton on February 27, 2024, 7:48 am
 
 
357
views
3
answers

molybdenum

By rrenn on December 1, 2023, 10:05 am
Last Reply: rrenn on December 27, 2023, 2:23 pm
 
 
292
views
2
answers

Depth of cut, single point threading

By Dell on October 1, 2023, 9:12 am
Last Reply: Eldar Gerfanov (Admin) on October 29, 2023, 3:58 pm
 
 
305
views
1
answer

Suggestions

By Conradio on July 24, 2023, 11:42 pm
Last Reply: Eldar Gerfanov (Admin) on July 27, 2023, 12:27 am
 
 
338
views
2
answers

Corner Rounding End Mill FSwizard and HSMA

By riplash2008 on July 5, 2023, 10:29 am
Last Reply: riplash2008 on July 12, 2023, 7:44 am
 
 
310
views
2
answers

A286 SS

By Framebuilder69 on September 18, 2022, 6:37 pm
Last Reply: Framebuilder69 on September 19, 2022, 10:05 pm
 
 
320
views
4
answers

Newbie question on boring

By StevenRosburg on August 22, 2022, 1:03 pm
Last Reply: StevenRosburg on August 27, 2022, 11:03 am
 
 
311
views
3
answers

Tormach 8L High Speed Profile

By Chris1050 on February 25, 2022, 11:07 pm
Last Reply: Eldar Gerfanov (Admin) on March 6, 2022, 2:46 pm
 
 
488
views
1
answer

Aluminium 5000 Series (5083) Feed in HSM to low or material inhomogenious ?

By aaronr on February 9, 2022, 6:07 am
Last Reply: Eldar Gerfanov (Admin) on February 26, 2022, 1:34 pm
 
 
420
views
3
answers

Trochoidal / peel

By doZrQ on November 3, 2021, 7:25 am
Last Reply: Eldar Gerfanov (Admin) on November 3, 2021, 9:16 am
 
 
546
views
1
answer

HSM Function How it works properly

By BryonF on October 19, 2021, 8:19 am
Last Reply: Eldar Gerfanov (Admin) on October 19, 2021, 9:08 am
 
 
726
views
5
answers

Work Flow using HSM Advisor

By capt.frito on December 20, 2020, 11:00 am
Last Reply: ndlsjk on April 8, 2021, 4:56 pm
 
 
417
views
4
answers

Small nitpick, incorrect thread nominal in Tap drill chart

By PhilipMes on June 2, 2020, 12:43 am
Last Reply: Eldar Gerfanov (Admin) on July 1, 2020, 3:38 pm
 
 
684
views
3
answers

Fusion 360

By bdrmachine on December 21, 2019, 2:15 pm
Last Reply: Test1test on July 1, 2020, 1:58 pm
 
 
310
views
5
answers

V1.708 pro decimal issue in corner radius

By cncjerry on May 20, 2020, 12:19 pm
Last Reply: cncjerry on May 29, 2020, 6:59 am
 
 
449
views
2
answers

To low Feed

By Morten on May 10, 2020, 1:31 pm
Last Reply: Morten on May 11, 2020, 1:47 am
 
 
8589
views
2
answers

Contact ?

By klausc on July 27, 2019, 5:37 pm
Last Reply: klausc on July 27, 2019, 7:48 pm

© 2009-2022 Eldar Gerfanov. All Rights Reserved.
© 2009 Eldar Gerfanov. Materials on this site are presented as is and are mostly for educational use.

You may freely reproduce information presented herein without any consent from me, provided you include link to this site.
In case when i am not the copyright holder, you may want to contact proper owner of material. Anyway, they are freely available on the Internet.
If you hold the copyright right for any of the materials on this site and want them removed, please contact me here