Discussions on general subject, as well as questions and suggestions concerning FSWizard in general
| 644 views |
3 answers |
Tutorial VideoBy therookie on September 14, 2025, 7:33 amLast Reply: Eldar Gerfanov (Admin) on December 4, 2025, 2:37 pm |
|
| 415 views |
Printed Circuit Board Milling- Hobby levelBy Mot on September 4, 2025, 6:24 pm |
||
| 430 views |
1 answer |
Future sharing of work accountBy TheHow7zer on March 21, 2025, 7:57 amLast Reply: Eldar Gerfanov (Admin) on March 22, 2025, 11:26 pm |
|
| 1830 views |
4 answers |
Request to add PU Epoxy Tooling Board density 45lb/ft^3By dhanushkk on December 10, 2024, 2:03 pmLast Reply: dhanushkk on December 13, 2024, 9:55 am |
|
| 2205 views |
3 answers |
Ball endmill/surfacing exampleBy rlockwood on September 18, 2013, 11:54 amLast Reply: Eldar Gerfanov (Admin) on September 19, 2024, 10:52 pm |
|
| 494 views |
3 answers |
HSMA speeds and feeds with plastic and O-flutesBy riplash2008 on January 5, 2024, 2:49 pmLast Reply: MikeHorton on February 27, 2024, 7:48 am |
|
| 429 views |
3 answers |
molybdenumBy rrenn on December 1, 2023, 10:05 amLast Reply: rrenn on December 27, 2023, 2:23 pm |
|
| 364 views |
2 answers |
Depth of cut, single point threadingBy Dell on October 1, 2023, 9:12 amLast Reply: Eldar Gerfanov (Admin) on October 29, 2023, 3:58 pm |
|
| 386 views |
1 answer |
SuggestionsBy Conradio on July 24, 2023, 11:42 pmLast Reply: Eldar Gerfanov (Admin) on July 27, 2023, 12:27 am |
|
| 447 views |
2 answers |
Corner Rounding End Mill FSwizard and HSMABy riplash2008 on July 5, 2023, 10:29 amLast Reply: riplash2008 on July 12, 2023, 7:44 am |
|
| 383 views |
2 answers |
A286 SSBy Framebuilder69 on September 18, 2022, 6:37 pmLast Reply: Framebuilder69 on September 19, 2022, 10:05 pm |
|
| 403 views |
4 answers |
Newbie question on boringBy StevenRosburg on August 22, 2022, 1:03 pmLast Reply: StevenRosburg on August 27, 2022, 11:03 am |
|
| 339 views |
3 answers |
Tormach 8L High Speed ProfileBy Chris1050 on February 25, 2022, 11:07 pmLast Reply: Eldar Gerfanov (Admin) on March 6, 2022, 2:46 pm |
|
| 559 views |
1 answer |
Aluminium 5000 Series (5083) Feed in HSM to low or material inhomogenious ?By aaronr on February 9, 2022, 6:07 amLast Reply: Eldar Gerfanov (Admin) on February 26, 2022, 1:34 pm |
|
| 506 views |
3 answers |
Trochoidal / peelBy doZrQ on November 3, 2021, 7:25 amLast Reply: Eldar Gerfanov (Admin) on November 3, 2021, 9:16 am |
|
| 649 views |
1 answer |
HSM Function How it works properlyBy BryonF on October 19, 2021, 8:19 amLast Reply: Eldar Gerfanov (Admin) on October 19, 2021, 9:08 am |
|
| 836 views |
5 answers |
Work Flow using HSM AdvisorBy capt.frito on December 20, 2020, 11:00 amLast Reply: ndlsjk on April 8, 2021, 4:56 pm |
|
| 500 views |
4 answers |
Small nitpick, incorrect thread nominal in Tap drill chartBy PhilipMes on June 2, 2020, 12:43 amLast Reply: Eldar Gerfanov (Admin) on July 1, 2020, 3:38 pm |
|
| 781 views |
3 answers |
Fusion 360By bdrmachine on December 21, 2019, 2:15 pmLast Reply: Test1test on July 1, 2020, 1:58 pm |
|
| 391 views |
5 answers |
V1.708 pro decimal issue in corner radiusBy cncjerry on May 20, 2020, 12:19 pmLast Reply: cncjerry on May 29, 2020, 6:59 am |
© 2009-2022 Eldar Gerfanov. All Rights Reserved.
© 2009 Eldar Gerfanov. Materials on this site are presented as is and are mostly for educational use.
You may freely reproduce information presented herein without any consent from me, provided you include link to this site.
In case when i am not the copyright holder, you may want to contact proper owner of material. Anyway, they are freely available on the Internet.
If you hold the copyright right for any of the materials on this site and want them removed, please contact me here