Latest Responses
- Cannot Update Tool Parameters by Eldar Gerfanov on March 19
- Favorite Materials List by Eldar Gerfanov on March 11
- Coatings PVD AlTiCrSiN by Eldar Gerfanov on March 3
- Threadmill questions by Eldar Gerfanov on February 27
- Spot drill feed rate by Eldar Gerfanov on February 22
- Add tool by Eldar Gerfanov on January 24
- Breakthrough amount in Calculation Report by Eldar Gerfanov on December 19
- Confusing Circle/Ramp output by Sperciv on October 28
Support forum for all FSWizard versions
2 topics |
0 answers |
FSWizard Beta Testers ForumLast activity in:READMEby: Eldar Gerfanov on May 19, 2020, 3:51 pm |
26 views |
1 answer |
Cannot Update Tool ParametersBy AmericanMakerCNC on March 19, 2023, 9:05 amLast Reply: Eldar Gerfanov on March 19, 2023, 9:49 am |
|
52 views |
1 answer |
mm/sec unitsBy paulvella on August 10, 2022, 3:17 amLast Reply: Eldar Gerfanov on August 15, 2022, 11:32 pm |
|
1990 views |
3 answers |
minimum RPMBy cncworkdork on August 16, 2013, 1:19 pmLast Reply: Eldar Gerfanov on June 5, 2022, 6:00 pm |
|
141 views |
1 answer |
More decimal placesBy shadowbane900 on December 17, 2020, 4:51 amLast Reply: Eldar Gerfanov on December 22, 2020, 10:46 am |
|
2442 views |
3 answers |
Clarification about the cutting forceBy raoul.lector on November 28, 2013, 5:03 pmLast Reply: Eldar Gerfanov on August 19, 2020, 8:35 pm |
|
115 views |
7 answers |
90deg Flat head screws only showing MMBy Blue_Chips on May 23, 2020, 2:26 pmLast Reply: Blue_Chips on May 24, 2020, 7:59 am |
|
241 views |
5 answers |
FSWizard not found in App Store - HelpBy phrotus on April 1, 2019, 9:13 amLast Reply: Shaeto on March 6, 2020, 7:35 am |
|
277 views |
2 answers |
Warnings for rubbing, deflection, etc.By Shassel on April 29, 2019, 1:12 pmLast Reply: Eldar Gerfanov on December 21, 2019, 2:55 pm |
|
216 views |
1 answer |
In per revBy Shassel on August 28, 2019, 5:16 amLast Reply: Eldar Gerfanov on August 31, 2019, 5:39 am |
|
182 views |
1 answer |
iOS Feed/Speed Pro does not lock valuesBy hoowahfun on August 16, 2019, 9:29 amLast Reply: Eldar Gerfanov on August 16, 2019, 1:34 pm |
|
166 views |
1 answer |
cant change toolBy cncholic on August 15, 2019, 5:27 pmLast Reply: Eldar Gerfanov on August 15, 2019, 7:08 pm |
|
566 views |
1 answer |
How to determine lthe lead angle on an endmillBy frido628 on June 28, 2019, 10:47 amLast Reply: Eldar Gerfanov on June 28, 2019, 11:08 am |
|
181 views |
1 answer |
Saving Speed and Feed Adjustments?By Splat on March 15, 2019, 6:57 pmLast Reply: Eldar Gerfanov on March 28, 2019, 10:43 pm |
|
186 views |
1 answer |
Drill Point Calc BrokenBy Flub on February 24, 2019, 8:09 amLast Reply: Eldar Gerfanov on February 24, 2019, 11:03 am |
|
221 views |
2 answers |
Flycutter (Tool Type)By Tonkatim on January 20, 2019, 2:52 pmLast Reply: Tonkatim on January 20, 2019, 3:19 pm |
|
75 views |
Inch tool diameter incrementsBy JackWSmach on January 11, 2019, 9:46 am |
||
194 views |
1 answer |
Feeds and speeds for countersinksBy stovall on November 18, 2018, 1:16 amLast Reply: Eldar Gerfanov on November 19, 2018, 5:18 pm |
|
273 views |
1 answer |
What does the slotting option do?By Groost on November 12, 2018, 12:47 pmLast Reply: Eldar Gerfanov on November 12, 2018, 3:24 pm |
|
302 views |
9 answers |
Bring back editing Chip load/RPM/Feed directlyBy Unr3aL on September 23, 2018, 7:11 amLast Reply: Unr3aL on October 25, 2018, 9:27 am |
|
194 views |
2 answers |
Insert lengthBy Jeff on August 29, 2018, 8:14 pmLast Reply: Jeff on September 7, 2018, 8:31 pm |
© 2009-2022 Eldar Gerfanov. All Rights Reserved.
© 2009 Eldar Gerfanov. Materials on this site are presented as is and are mostly for educational use.
You may freely reproduce information presented herein without any consent from me, provided you include link to this site.
In case when i am not the copyright holder, you may want to contact proper owner of material. Anyway, they are freely available on the Internet.
If you hold the copyright right for any of the materials on this site and want them removed, please contact me here