Subscribe to Blog
Email Address
 

Pages:(29) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 [28] 29

Programming Efficient Peck Drilling Cycle

June 2, 2012, 8:18 am by Eldar Gerfanov

Using Peck Cycle is often needed when drilling deep holes.
When using proper feed and speed no peck is required at depths of up to 3xDia for regular or 5xDia for High-Performance Parabolic drills.
At depths up to 10x, up to 5 pecks are required for regular  drills and up to 3 for Parabolic.
Anything over 10x Dia requires constant pecking of 0.5-1x Dia for regular drills and 1.5-2 Dia for Parabolic.

Since for programming you need a peck amount. Here are the numbers:

Code:REGULAR JOBBER DRILLS
3x: No Peck
3x-10x: 1xDia Peck
over 10x:.75xDia Peck
over 15x:.5xDia Peck 
 

Code:HI-HELIX HP DRILLS
5x: No Peck
5x-10x: 2xDia Peck
over 10x: 1.5xDia Peck 

Of course our HSMAdvisor Speed and Feed Calculator suggests not only the Speeds and Feeds but also the proper peck depth for various drill types and depths of the hole.
It in fact was the first machinist calculator to do so. This feature was much later borrowed by our competition.

And here is a pretty image showing Peck VS Hole Depth for regular twist drill:

This not only means that peck amount should be different for different styles of drills and depths of holes.
But also that peck distance should be different for different stages of drilling the same hole.
Ideally we should start the hole with large pecks, that continually reduce as the hole gets deeper and deeper.

Let's find out how we can apply this knowledge when programming our toolpaths.
This is format for normal Pecking:

Read More 


okuma prog samples

April 27, 2012, 12:43 pm by Eldar Gerfanov

Here are some Okuma Captain 1200 program samples for work with live tooling.
Samples are quite big so READ full article

Read More 


Compound Cycle Tapping on Okuma Lathe

April 27, 2012, 11:56 am by Eldar Gerfanov

Cycle Format:

G184 X Z C K (I) F Q E
OR
G184 X (Z) R C K (I) F Q E

G180 (Cancel)

Read More 


FS Wizard: Dormer Drill test on T6061 Aluminum

April 23, 2012, 7:22 pm by Eldar Gerfanov

As part of FS Wizard's development. 2 drills were tested today on T6061 Aluminum.

0.312 Dia and 0.390 Dia Dormer A002 Drill Jobber Drill with TiN coated tip.

Helix:30Deg

Point:Split, 118Deg.

Hole depth for both was 3.0"".

Peck equaled 1xDia

Speeds and Feeds for 0.312 Dia drill were

Read More 


Drilling Hardox 500 55RC: 0.281 dia .75 deep

April 20, 2012, 12:47 am by Eldar Gerfanov

Tool:0.281 dia 0 helix TIN coated carbide drill

Peck:0.125

Coolant: Air

RESULT
SFM: 49 f/min
RPM: 663
APT:  0.00070 in/rev
Feed: 0.93 in/min
MRR: 0.1 in^3/min
HP: 0.2
Torque: 19.4 in-lb
Max Torque: 22.9 in-lb

 


Test of NIAGARA 3FL HP End mill for Aluminum

February 27, 2012, 10:02 pm by Eldar Gerfanov

Recenty ordered a 3Flute High Performance End Mill From NIAGARA.
Was very glad and slightly surprised that when punched in all of the endmill's data into my Calculator nothing broke down.I had a rason: At 5000RPM and 3/8" Deep slot cut. The feed came to around 92.0IPM. Chips were making this nice ringing noise that sounds like money.

Setup:
HAAS VM-3
Hudrolic Tribos Holder
3/4" 45DegHelix 3Flute 1.625FluteLen, 2.375"Overhang TICN HP End mill

S:5000RPM
F:92.0IPM
DOC: 0.375" Slotting
Coolant:FLOOD

The calculation was pretty much dead on.


Tapping Hardox Rc 45-50

February 27, 2012, 9:43 pm by Eldar Gerfanov

A need arouse to drill and tap lots of blind 1/4-20 holes in 3/4" thick hardox 45-50RC hard plate.

So if you ever need to do this use:

1) DRILL
Tap hole: >0.202" or bigger.  5/8 deep.
Drill used: Tialn coated carbide drill.
S=1418 RPM
F=2.6 IPM
NO Peck, No Coolant

2)TAP
Read More 


Renishaw OTS tool probe cycle for HAAS can set both length and diameter offsets.

Too bad there is no choice: it only puts absolute measured diameter of the tool into D- diameter offset and makes wear offset=0

But if your programming is done with the center of the cutter, then you actually only need the difference between actual and programmed diameters of the tool.


I.E.: When probing 5/8Dia end mill, we get D=0.6248. You would normally have to subtract 5/8 from it and leave the -0.0002 difference.

But there is an easier way

Read More 


HAAS: Making G54-G59 show Z0 at the top of fixture

November 29, 2011, 10:50 pm by Eldar Gerfanov

Problem: Work offset G54 Z0 shows some "weird number" which is very hard to relate to.

Can we make top of fixture show Z0=0.000 ?

Solution:

Read More 


FSWizard: Online CNC Machinists Calculator

October 14, 2011, 8:33 pm by Eldar Gerfanov

FSWizard Online is:

FSWizard is here

It is the most accurate Online Feeds and Speeds Calulator.

In order for every user to enjoy latest modifications and most accurate results, it is WEB Based.
This means that you can use it across all imaginable operational systems and devices.
All you need is an internet connected WEB browser.
No download or installation is required: Just visit the web page.

Also a full functioning mobile version is available.

Key Features of FSWizard:

Read More 


Pages:(29) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 [28] 29

Sing In

© 2009-2018 Eldar Gerfanov. All Rights Reserved.
© 2009 Eldar Gerfanov. Materials on this site are presented as is and are mostly for educational use.

You may freely reproduce information presented herein without any consent from me, provided you include link to this site.
In case when i am not the copyright holder, you may want to contact proper owner of material. Anyway, they are freely available on the Internet.
If you hold the copyright right for any of the materials on this site and want them removed, please contact me here