Discussions on general subject, as well as questions and suggestions concerning FSWizard in general
Pages:(4) [1] 2 3 4
 
 
67
views
3
answers

HSMA speeds and feeds with plastic and O-flutes

By riplash2008 on January 5, 2024, 2:49 pm
Last Reply: MikeHorton on February 27, 2024, 7:48 am
 
 
93
views
3
answers

molybdenum

By rrenn on December 1, 2023, 10:05 am
Last Reply: rrenn on December 27, 2023, 2:23 pm
 
 
77
views
2
answers

Depth of cut, single point threading

By Dell on October 1, 2023, 9:12 am
Last Reply: Eldar Gerfanov (Admin) on October 29, 2023, 3:58 pm
 
 
104
views
1
answer

Suggestions

By Conradio on July 24, 2023, 11:42 pm
Last Reply: Eldar Gerfanov (Admin) on July 27, 2023, 12:27 am
 
 
108
views
2
answers

Corner Rounding End Mill FSwizard and HSMA

By riplash2008 on July 5, 2023, 10:29 am
Last Reply: riplash2008 on July 12, 2023, 7:44 am
 
 
119
views
2
answers

A286 SS

By Framebuilder69 on September 18, 2022, 6:37 pm
Last Reply: Framebuilder69 on September 19, 2022, 10:05 pm
 
 
145
views
4
answers

Newbie question on boring

By StevenRosburg on August 22, 2022, 1:03 pm
Last Reply: StevenRosburg on August 27, 2022, 11:03 am
 
 
142
views
3
answers

Tormach 8L High Speed Profile

By Chris1050 on February 25, 2022, 11:07 pm
Last Reply: Eldar Gerfanov (Admin) on March 6, 2022, 2:46 pm
 
 
270
views
1
answer

Aluminium 5000 Series (5083) Feed in HSM to low or material inhomogenious ?

By aaronr on February 9, 2022, 6:07 am
Last Reply: Eldar Gerfanov (Admin) on February 26, 2022, 1:34 pm
 
 
198
views
3
answers

Trochoidal / peel

By doZrQ on November 3, 2021, 7:25 am
Last Reply: Eldar Gerfanov (Admin) on November 3, 2021, 9:16 am
 
 
265
views
1
answer

HSM Function How it works properly

By BryonF on October 19, 2021, 8:19 am
Last Reply: Eldar Gerfanov (Admin) on October 19, 2021, 9:08 am
 
 
427
views
5
answers

Work Flow using HSM Advisor

By capt.frito on December 20, 2020, 11:00 am
Last Reply: ndlsjk on April 8, 2021, 4:56 pm
 
 
248
views
4
answers

Small nitpick, incorrect thread nominal in Tap drill chart

By PhilipMes on June 2, 2020, 12:43 am
Last Reply: Eldar Gerfanov (Admin) on July 1, 2020, 3:38 pm
 
 
487
views
3
answers

Fusion 360

By bdrmachine on December 21, 2019, 2:15 pm
Last Reply: Test1test on July 1, 2020, 1:58 pm
 
 
137
views
5
answers

V1.708 pro decimal issue in corner radius

By cncjerry on May 20, 2020, 12:19 pm
Last Reply: cncjerry on May 29, 2020, 6:59 am
 
 
238
views
2
answers

To low Feed

By Morten on May 10, 2020, 1:31 pm
Last Reply: Morten on May 11, 2020, 1:47 am
 
 
4669
views
2
answers

Contact ?

By klausc on July 27, 2019, 5:37 pm
Last Reply: klausc on July 27, 2019, 7:48 pm
 
 
869
views
8
answers

Material hardness vs cutting parameters

By Yosiu on March 11, 2018, 11:44 pm
Last Reply: Gmack on June 17, 2019, 11:46 am
 
 
204
views
1
answer

Invar 36

By Jncarabello on May 27, 2019, 2:26 pm
Last Reply: Eldar Gerfanov (Admin) on May 27, 2019, 5:38 pm
 
 
399
views
1
answer

Dry vs wet SFM

By Jncarabello on November 24, 2018, 5:55 pm
Last Reply: Eldar Gerfanov (Admin) on November 24, 2018, 6:36 pm

© 2009-2022 Eldar Gerfanov. All Rights Reserved.
© 2009 Eldar Gerfanov. Materials on this site are presented as is and are mostly for educational use.

You may freely reproduce information presented herein without any consent from me, provided you include link to this site.
In case when i am not the copyright holder, you may want to contact proper owner of material. Anyway, they are freely available on the Internet.
If you hold the copyright right for any of the materials on this site and want them removed, please contact me here